Taking care of your garden yourself: Step by step for the perfect lawn
Decided to set up your robotic lawn mower yourself? We'll walk you through what to look out for and the best order to do things in. And of course you can always find more detailed information in the supplied operating instructions. These are also available for download here and in the Einhell Service Shop.
Preparation is key
It is always advisable to make a sketch in advance – no matter how large or small a garden may be. In the sketch, draw the boundaries of the garden, the house, obstacles, paths, bushes, flower beds, trees, furniture, large ornaments and areas of water. If you have an overview of your garden, you'll be able to plan out on paper how and where you ideally want to lay the boundary cable before you get started.
If the planning is in place, you should – ideally before you lay the cable – manually trim any grass that has grown higher than 6 cm one last time with a lawn mower or trimmer. If you then programme the mowing times sensibly, the grass should not be able to grow this tall again over the entire garden season. The new robotic lawn mower takes care of this at regular intervals. Before it is ready to get going, loose objects such as toys should also be removed from the lawn.
Tip: If you have very hard or dry soil, the fastening hooks may break when pressed into the soil. Here it helps to water the soil beforehand.
Sketching: Mowing zones and charging station position
You can now find out how to choose the limits of your mowing surfaces on the plan you have prepared. First, you'll need to find a suitable position for the charging station. For the station, you need an external power socket with permanent power supply in a dry place, protected from sun and rain. For additional weather protection, you will also find a robotic lawn mower garage as an accessory in the Einhell range. The charging station should also be placed on a level surface at the level of the turf sward. Behind the charging station, the boundary cable should run straight for at least 1 metre before making the first bend. In front of the charging station, i.e. on the side where the robotic mower enters and leaves the station, the wire should run straight for at least 2 metres.
Depending on whether your FREELEXO model has the multi-zone mowing function, you can think about whether it makes sense to define different starting points for your robot. This is how you determine on which days which zones are to be mowed. The FREELEXO models with the designation BT+ are also equipped with a second area mowing program. This allows you to define demarcated adjoining areas as a mowing surface by means of a boundary cable. For the robot can get to work there, you simply place it on the respective surface. Since no charging station is placed there, you should then carry it back to the main area of the charging station.
The charging station should be placed on a nearby power connection protected from the rain and sun.
Get your accessories ready
Depending on which robotic mower you have chosen, the necessary accessories – such as sufficient boundary wire, fastening hooks and connecting clamps – will already be included in delivery. A small ruler for measuring the distance between the boundary cable and obstacles is usually also included. You will also need the following accessories to install the boundary cable:
- Wire stripper
- Possibly: Spirit level, metre stick
Positioning the charging station and charging the robotic lawn mower
After you have positioned the charging station in a suitable place, you can connect it. For this purpose, the station is simply connected to the power supply and the mains plug is plugged into the socket. Once the power supply has been established, a green LED light flashes at the front and rear of the station. You can then insert the Power X-Change battery into the robotic lawn mower and drive it into the station yourself for charging.
Laying the boundary wire
Basically, there are two ways to lay the boundary cable: above ground with fastening hooks and underground by burial. However, if you are laying the wire for the first time or if you plan to redesign your garden in the near future, you should lay it above ground for the time being. This makes it easier to make corrections without having to dig out the wire. By the way: If the wire is laid above ground, it will be overgrown after a short time, because it is laid very close to the ground. As a rule, it will no longer be visible by the next gardening season.
When laying the boundary cable, it is important to maintain the correct distances and to delimit all necessary obstacles. In addition, parallel wires should never overlap. So make sure you always place the cables parallel to each other.
Watch our video to find out what distances you should keep and how best to proceed. You can also find more information in the operating instructions.
Connecting the charging station and setting up the robotic lawn mower
If the boundary wire has been laid and the robotic lawn mower has been charged, the station can be connected to the wires. Before you do this, you must disconnect it from the power supply. Both ends of the boundary cable are then stripped and inserted into the provided connections. For this purpose, the end of the cable that comes from the front side of the station, is passed through a channel on the underside of the charging station and inserted into the connection provided. The wire end coming from the rear is connected to the other connection. The best way to find out which cable is to be plugged into which connection is to refer to the operating instructions! Make sure that the cables do not cross each other! After the charging station has been reconnected to the power supply, the control LED will be a solid green when the cables are properly connected.
Test drive and setting up the robotic mower
Before you can programme regular mowing times, you should check whether you have laid your cables correctly. A first test drive of the FREELEXO is planned for this purpose. You can find out how to do this in the following video.